DRGW - Durango Division National Model Railroad Association

John Vandenberg
Denver & Rio Grande Western, Durango Division
800 square ft
Colorado mountains
Stacks Image 99363
Stacks Image 99366
Stacks Image 99369
Stacks Image 99243
About the Layout
The Durango Division of the Denver and Rio Grande Western is based on the heart of narrow gauge country in America, Durango Colorado. From Durango the railroad serves the 4 points of the compass, north to Silverton,south to Farmington, east to Chama, and west to Dolores via the Rio Grande Southern. Silverton is also served by the Silverton Northern which ran northeast from Silverton to serve the mills at Silverlake, Eureka, and Animas Forks.

The HOn3 version of the Durango Division is being built as a double deck railroad with the Durango yard splitting the two decks. So far about three quarter of the track is completed. All the track on the upper deck, Durango yard, Rio Grande Southern, and Silverton Northern is complete and basic scenery is in on most of the upper deck. A temporary staging yard is in place on the lower deck to represent Chama. The line to Farmington is now complete so long pipe trains are now part of the operations.

The railroad is run with limited time table-train order without a dispatcher. Once the lower deck is in, a formal timetable will be published and a dispatcher will be needed.

In the era modeled, 1948-1953, only a couple of time table trains were left, with most freights run as extras. Currently most trains show up on the

A 3-1 fast clock is used for three eight hour sessions to make up a full day. The operating system is Digitrax with some Soundtraxx decoders.

Six operators are needed to fully operate the railroad. The jobs include Yard master, two yard goats, and three road crews which operate the way freights, the Rio Grande Southern, and Silverton Northern.
Layout at a Glance 
Stacks Image 996
Layout at a glance
  • HOn3
  • Prototype-Denver and Rio Grande Western, Rio Grande Southern, Silverton Northern
  • Location: southwest Colorado and southwestern New Mexico
  • Size: 800 square feet
  • Layout design: double deck point to point.
  • Command system-Digitrax
  • Locomotives-All steam, about half with Soundtraxx decoders
  • Scenery-About 25 percent finished, 100 percent roughed in hardshell

Photo Gallery

Stacks Image 99263
The Barto Ore Complex is located on the Silverton Northern between Silver Lake and Eureka. This fictional structure came from an earlier layout, and like most structures is scratch built.
Stacks Image 99266
Eureka on the Silverton Northern looking toward the Sunny Side Mill. The foundations for this huge prototype mill can still be seen today in Eureka, Colorado.
Stacks Image 99269
A look at where the refinery in Farmington will be located. The small prototype refinery supplied gasoline and other petroleum products for a number of dealers and industries in the Southwest along the D&RGW and RGS.
Stacks Image 99272
Here is the “old smelter” that was located across the Animas River from Durango. The Rio Grande Southern main line runs through the Smelter instead of by it as the prototype did on its way from Dolores, CO to Durango, CO.
Stacks Image 99275
The main isle of the Durango Division. On the upper level is the Silverton Northern as it heads up to Silver Lake, Eureka, and finally Animas Forks. To the left on the lower level is Farmington and on the Right is the main line through Gato on its way to Chama. The Rio Grande Southern is runs on the middle level on its way to Dolores.
Stacks Image 99278
Carbon Junction is located a few miles south of Durango and is where the Farmington Branch splits off the main line.
Stacks Image 99281
A look at the Durango engine service facility. In the background you can see your Prairie Rail Committee members from left to right is John Vandenberg, Bert Overholtzerhouser, Bill (wild man) Hurt, and Howey Gellesspee. While Howey is not a committee member, he is a hell of a nice guy, I think.
Stacks Image 99284
Another look at Carbon Junction
Stacks Image 99287
Looking South in Silverton
Stacks Image 99290
To pay homage to my Standard Gauge Brothers, I included a section of Duel Gauge track in Aztec. The Farmington Branch was originally built as a Standard Gauge branch out of Durango and was converted to narrow Gauge in 1923.
Stacks Image 99293
A view of the Silverton Northern engine house. The structure still stands today and is used to house the recently rebuilt D&RGW 315.
Stacks Image 99296
A nice view of the Depot at Silverton. However nice it is, it is one of the few structures the owner did not build.
Stacks Image 99299
One of the great views on the railroad. This trestle is located on the Silverton Northern just outside Silverton. This simple bridge crosses over the Animas River on a 7% grade and is in the middle of a 18” curve. Makes for great operations when SN #10, a 10 ton Benson Shay, pushes up cars with her cylinders facing you.
Stacks Image 99302
Looking south down the Durango Yard. The D&RGW’s narrow Gauge revolved around Durango. To the North is Silverton, to the east is Doloros, Farmington was to the south, and Chama to the east.
Stacks Image 99305
One of the big K series 2-8-2’s has been serviced and has beep hostled onto the engine ready track. I tried to model this part of Durango to the scale foot.
Stacks Image 99308
A great, though distorted, of Durango. Durango spans the width of the room and is about 23’ long. It is built to be worked from both sides and two duck-under’s provide access. As per the prototype it is divided into four distinct yards. The south yard was the arrival/departure tracks. The middle yard was the passenger yard. The north yard was where the car classification was done. And the roundhouse, turntable, engine service, and car shops round out the rest of Durango.
Stacks Image 99311
The newest structure on the layout is this Fine Scale Miniatures kit. They should change their name to Fine Scale Scratch Building. I have not yet come up with a name for it, although I am thinking of “Peckerwood Coal” I am open to suggestions for another name.
Stacks Image 99314
Looking up the 7% grade from Silverton to Eureka on the Silverton Northern. The Silverton Northern had about 7 miles of 7% grade between Eureka and Animas Forks. This part of the Silverton Northern only lasted a few years as it was closed a good portion of the year due to snow and snow slides.
Stacks Image 99317
Again, looking south in Durango. The north yard can be seen as well as the passenger station.
Stacks Image 99320
This is a good look at the car shops in the Durango yard. Keith Robinson can be seen taking a pic for this website. Guess which one it is.
Stacks Image 99323
Looks like engine 475 is in need of a bit of maintenance in this view toward the turntable and roundhouse.
Stacks Image 99326
Here we are looking at the back side of the car shops. I like to say that the Durango car shop is a working car shop. Bad order cars are placed on the north side of the shop. When they are “rebuilt” with Blackstone trucks and it is ready to operate, I place it on the south side of the car shop ready to be picked up and sent to its destination.
Stacks Image 99329
A great view of Silverton Northern shay #12. It is a 10 ton Benson Shay that has new motor and the smallest decoder I could find in it. There are times when it is the best running engine on the entire railroad, and other times when it won’t run a foot without problems.
Stacks Image 99332
Another great view of “Peckerwood Coal”.
Stacks Image 99335
A nice view of the Barto Ore Complex. I began scratchbuildng this structure over 25 years ago and it has continued to grow over the years. The latest edition is the cut stone walls that hold the structure to the slope of the hill.
Stacks Image 99338
In the panorama view of the Barto Ore Complex, we can see about ¼ of the Silverton Northern. On the far left we can see the Silver Lake spur and mill. To the far right we can see Eureka almost all the way to the Gold Prince.
Stacks Image 99341
Silverton Northern number 34 is spotting cars at the Gold Prince. The foundations of the Gold Prince Mine can still be explored today.
Stacks Image 99344
Looking north at Farmington we can see the mainline from Chama on the right. The bare concrete pad by the water tower is where the station will be located.
Stacks Image 99347
The Silver Lake Mill was located just outside Silverton. I have mocked up the structures in styrene and gave them a coat of brown paint to see how they will look before I build the scale model of it.
Stacks Image 99350
Goose 7 ready to depart Dolores on its morning trip to Durango.
Stacks Image 99353
Blackstone models C-19 D&RGW 345 is pulling the San Juan passenger train across a bridge on its way to Chama. The westbound San Juan will meet the Eastbound at Gato. Please excuse the speaker on top of the tender. I tried to fit it in before the session, but did not get the chance.
Stacks Image 99356
Another shot of D&RGW 345 crossing the bridge near Chama.